Sherwood Newcastle R-865 Manuel d'utilisateur Page 63
- Page / 79
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
ENGLISH
63
When selecting the DECODING MODE, SURROUND MODE, DYNAMIC RANGE
• Each time these buttons are pressed, “ ” and “ ” are
moved to the corresponding mode.
• Each time these buttons are pressed, the modes change as
follows according to the selected item :
When DECODING MODE is selected
• Depending on the input digital signal format, you can select the desired decoding mode.
AUTO : Select this for automatic detection of a digital input signal format.
The input digital signal format (DTS, Dolby Digital, MPEG or PCM(2 channel stereo), etc.) used by the
selected digital input source is detected automatically to perform the necessary decoding process for
optimum surround modes.
DOLBY DIGITAL : Select this for Dolby Digital signal processing. The decoding process is preformed only when
Dolby Digital signals are input.
DTS : Select this for DTS signal processing. The decoding process is performed only when DTS signals are input.
MPEG : Select this for MPEG signal processing. The decoding process is performed only when MPEG signals are
input.
PCM : Select this for PCM signal processing. The decoding process is performed only when PCM signals are input.
Notes :
• Surround sound effect will not work properly if the signal passes through a graphic equalizer.
Please refer to your equalizer operating instructions for guidance on switching off(or defeating) the equalizer.
• Only when the digital input is selected as signal input for the input sources except TUNER and TAPE MONITOR,
the decoding mode can be selected.
• Noise may be generated at the beginning of playback and while searching during DTS playback in the auto mode.
In this case, try playing in the DTS mode.
Notes :
• Only when the digital input is selected as signal input, the decoding mode and the surround mode can be both selected as
desired.
• When the analog input is selected, only the surround mode can be selected as desired.
• When the 8 CH DIRECT is selected as an input source, you cannot perform the surround setup.
SURROUND SETUP
RETURN: B ack , : S e l e ct
DECODING MODE :
SURROUND MODE :
DOLBY D I G I TAL EX
+ NONE
DYNAMIC RANGE : 0 . 0
PL I I x MUS I C PARAMETER
AUTO
To select the desired decoding mode.
To select the desired surround mode.
To select the desired Dolby surround mode.
To adjust the dynamic range as desired.
To adjust the PL IIx MUSIC PARAMETER as desired.
Press the CURSOR UP( )/DOWN( ) buttons to select the desired item.
1
Press the CURSOR LEFT( )/RIGHT( ) buttons to select the desired mode.
2
SETTING THE SURROUND SETUP
- Audio/Video Receiver 1
- Introduction 2
- SAFETY INSTRUCTION 3
- CONTENTS 4
- System Connections 5
- Tape deck, MD recorder, etc 6
- Additional tape deck. etc 6
- CD player, etc 6
- TV, Projector, etc 7
- 5. CONNECTING 8CH DIRECT INs 8
- 6. CONNECTING PREOUTs 9
- 7. CONNECTING SYSTEM CONTROL 9
- 8. CONNECTING DC TRIGGER OUT 9
- 9. CONNECTING SPEAKERS 10
- Speaker placement 11
- the speakers 12
- PC with RS-232C port 13
- To a wall AC outlet 13
- 17 18 19 20 21 22 23 14
- 26 27 28 29 30 31 32 33 14
- VIDEO 4 INPUT JACKS 15
- FLUORESCENT DISPLAY 15
- LOADING BATTERIES 18
- 5 to 15 cm 21
- (2 to 6 inches) 21
- VOL DELETE PLAY CH 25
- Another room(Room 2) 27
- IR receiver 27
- (Multi-room system kit) 27
- Operations 28
- D I G I T A L 31
- SURROUND SOUND 31
- ENJOYING SURROUND SOUND 34
- (“” lights up) 36
- (“” light up) 36
- SUBWOOFER 37
- BAND FREQUENCY 39
- Image source 42
- Sound source 42
- Unit : minutes 44
- Using the OSD 47
- OSD Menu Settings 47
- Variable 48
- POWER AMP ASSI GN 49
- ROOM 2 49
- RETURN:Back , : Select 51
- SPEAKER DISTANCE 51
- VIRTUAL SPEAKER SETUP 52
- Result report 55
- RETURN:Back ENTER:Se l ec t 56
- AUTO SPEAKER SETUP 56
- SETTING THE SYSTEM SETUP 57
- C I NEMA EQ : 58
- TONE DEFEAT : 58
- COMPONENT V IDEO SETUP 59
- DC TRIGGER : 61
- T UNER V IDEO 1 61
- CD V IDEO 2 61
- AUX VIDEO 3 61
- TAPE MON. VIDEO 4 61
- When selecting the A/V SYNC 62
- SETTING THE SURROUND SETUP 63
- (original surround mode) 64
- PANORAMA : 65
- CENTER WIDTH 65
- DIMENSION 65
- SETTING THE CH LEVEL SETUP 66
- Troubleshooting Guide 71
- Specifications 72
- Setup Code Table 73
- AUX-TAPE 77
- AUX-TAPE/MD 77
- AUX-ACCESSARY 78
- AUX-HOME AUTOMATION 78
- 5707-04745-001-1 79
Produits connexes et manuels pour Récepteur Sherwood Newcastle R-865
(63 pages)
Récepteur Sherwood A-965 Spécifications
(11 pages)
(11 pages)
(22 pages)
(52 pages)
(52 pages)
Récepteur Sherwood R-945 Guide de dépannage
(32 pages)
(32 pages)
Récepteur Sherwood HSB-6501 Spécifications
(32 pages)
(32 pages)
(58 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.214 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels