Sherwood RVD-8090R Guide de dépannage télécharger pdf (Page 11)

ENGLISH

ADJUSTING SPEAKER SETTINGS

Operations

Adjusting the speaker settings

With the receiver in any of the

surround modes, press the

SPEAKER MODE button for

more than 2 seconds to enter

the front-center-rear speaker

set-up mode.

Select the desired speaker

setting.

󳀏The existing front-rear-center speaker setting is

displayed.

󳀏This set-up mode is not available when 6 CH DIRECT

is selected as the input source or when ANALOG is

selected as the signal input in the STEREO mode.

󳀏This receiver is equipped with circuitry that allows

the use of a wide range of speaker systems.

󳀏This circuitry works by redirecting the bass

frequencies or the entire channel to speakers that are

capable of reproducing them.

󳀏When a large or full range speaker capable of deep

bass response is used for one of the channels, that

channel should be set to L.

󳀏When a small or satellite speaker with limited bass

capability is used, that channel should be set to S.

Deep bass from that channel will be redirected to the

main left and right speakers or to the subwoofer.

󳀏When there is no speaker available, that channel

should be set to N. All the information in that

channel will be redirected to other available speakers.

󳀏Each time this button is pressed, one of 11 different

speaker settings is selected and displayed for 8

seconds as follows;

FL--CS--RS, FL--CL--RS, FL--CL--RL,

FL--CL--RN, FL--CS--RL, FL--CN--RL,

FL--CS--RN, FL--CN--RS, FS--CS--RS,

FS--CS--RN and FS--CN--RS.

󳀏In the above, F stands for Front Speakers, C for

Center Speaker, R for Rear Speakers, L for Large,

S for Small and N for None.

󳀏Large speakers are capable of deep bass response

and typically have one driver with a cone that is

10″(25 cm) or larger.

󳀏The following speaker settings cannot be selected:

Front, Small : Center, Large : and Rear, Large(FS--

CL--RL) : or Center, None and Rear, None(CN--

RN).

Select the desired

subwoofer setting.

󳀏Your requested speaker settings are entered into

memory and the set-up procedure advances to the

subwoofer mode.

󳀏If the speaker setting display disappears before the

MEMO/ENTER button is pressed, you must start

again from Step 1, above.

󳀏Each time this button is pressed, the subwoofer

setting changes and is displayed for 8 seconds as

follows;

↓

SUB W(oofer) -- Y(es): When using a powered

↓

subwoofer.

SUB W(oofer) -- N(o) : When not using a powered

subwoofer.

󳀏If the front speakers are set to S(mall), the

subwoofer is automatically set to “Y”.

Memorize the desired speaker

settings. Press the MEMO/

ENTER button while your

choice is displayed.

󳀏Your requested subwoofer setting is entered into

memory.

󳀏If the subwoofer display disappears before the

MEMO/ENTER button is pressed, you must start

again from Step 1, above.

󳀏Each time this button is pressed briefly, the front-

center-rear speaker or subwoofer setting is

displayed.

Memorize the subwoofer

setting. Press the

MEMO/ENTER button while

your choice is displayed.

Checking the speaker setting

SPEAKER MODE

MEMO/ENTER

ENGLISH

SPEAKER MODE

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 24 25

Commentaires sur ces manuels

Pas de commentaire

Sherwood RVD-8090R Guide de dépannage Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV Sherwood RVD-8090R